CAV hydrostatic, magazine bar feeders engineered exclusively for Cincom models M16, L20 and M20

No other bar feeder is built exactly like a CAV… because CAV, and only the CAV, is engineered for use exclusively with Cincom Swiss-type turning centers. Instead of compromising to meet the needs of many machines, CAV is specialized to meet just one.

 

That means:

  • It’s perfectly configured to the speeds, torque, power, and axis movements of the Cincom machine, allowing it to respond with the precise movements needed for optimum precision, performance, and productivity.
  • It’s able to share components. The CAV and the Cincom share the same CNC controller, and the same electrical system.
  • Space requirements are reduced, and the combination CAV bar feeder/Cincom turning center assures exceptional quality at an affordable price.

 

And more:

  • Fully enclosed system
  • Quick change separation system
  • Automatic remnant retraction
  • Quicker response between the bar feeder and the machine’s sliding headstock
  • Improved accuracy when specs are critical
  • A unique stabilizing mechanism to minimize wear and downtime
  • And just one company to contact for parts and service

Versatility

 

The Cincom bar feeder is equipped to handle round, square and hexagonal stock with diameters from .078" to 3/4" and lengths to 13’. There’s no need for chamfering. A spring-loaded end collet centers new bars at the center of the spindle for easier, wear-free operation. Only burrs and rough edges need to be removed.

 

Better Work Environment

 

Integrated hydraulic tank, oil pump and oil level indicator, plus reduced wiring and the absence of a separate control help to remove unnecessary clutter from passageways and the work area.

Machine specifications

Bar profiles round, hexagonal, square
Maximum bar length 13'
Bar stabilization Oil supply to the guide rail.
Intermediate three-roller support and
rear-end four roller support.
Attached with an oil splash prevention guide rail shutter.
Bar rack width 10.25"
Bar supply method Disk feeding
Control Operation and synchronous control by NC lathe
Power source AC200/220V, 50/60Hz (supplied from the NC lathe)
Weight (without oil) 2400 lbs.
C16/M16 L20/M20
Bar diameter range .078" ~ .625" .078" ~ .75"
Oil ISO VG68/351 ISO VG68/451

CAV Bar Stabilizing System

Cincom’s unique bar and spindle stabilizing mechanism aligns precisely the bar’s center of rotation with the center of the spindle. Forces are evenly distributed, protecting the spindle from excessive wear.

Oil/Roller Support System

As the bar rotates, it becomes hydrostatically supported in a bath of oil, and perfectly centered in the guide channels. Even with full-length, 13' bars, the lathe can operate noise-free and vibration-free at speeds to 12,000 rpm.

Windows®-Based Controls

Bar feeder movements can be viewed and controlled from the lathe’s CNC. A single controller, rather than two, allows for faster setups, easier operation, and total control from a single console.

Z-Axis Movement

Movements of the bar feeder are automatically programmed as an additional Z-axis on the turning center’s CNC. All bar feeder movements mirror exactly the movements in the lathe. The result is superior precision and maximized productivity.

Space-Saving Pusher Design

An auxiliary device pre-positions the bar. Forward and back motion is controlled by a servo that's connected directly to the lathe’s CNC. The bar positions to tenths accuracy with no following error. Insertion and braking response times are instantaneous.

Dimensions

All specifications are subject to change without prior notice.

 

This product is subject to the export control laws of the United States and other countries. A license may be required prior to export, re-export or transfer of these products. Contact us for further information.

 

Terms and Conditions

Marubeni Citizen-Cincom, Inc.

40 Boroline Road

Allendale, NJ 07401

Phone: 201-818-0100

Fax: 201-818-1877

Parts Fax: 201-818-1816